Baxter Creek Tools Co. Inc.
Sander Sitter
The Sander Sitter is a unique accessory that
works with 5”&
6” Random Orbital Disc Palm Sanders (ROS). The Sander Sitter allows the
operator of a ROS to safely set the Sander down in the carousel while running
to free up hands in order to manoeuvre work surfaces. As it is spinning in the
carousel the natural crepe rubber cleaning pad is eliminating 70 to 80% of the
debris from the sanding paper disc. It is also utilized in the process of
shutting off the Sander, by placing it in the carousel and letting it wind down
and stop safely in one place.
Instructions
**STEPS 1 & 2 ARE VERY
IMPORTANT**
*1: The first time you
use a new Sander Sitter, spread some sanding dust on the crepe rubber cleaning
pad to eliminate the sticky texture of the new cleaning pad. The sander has to
slide on the pad in order to operate smoothly.
*2: Be sure the sanding
disc is centred on the Sander, and the excess overlap of the sand paper is
rolled upwards. The first few times you must do this manually with the palm of
your hand, eventually the Sander Sitter will do this automatically. This
ensures enough room for movement in the carousel in order for the ROS. to
rotate and not shake.
**Note** All
brands of sandpaper come in different sizes they could be + OR – 5” it is
impossible for us to compensate for this, the Sander Sitter has been accurately
designed to accommodate the variable and performs at it’s maximum if the
previous instructions are followed correctly
3: Do not start the sander while it is sitting
in the carousel. After sanding, place the ROS directly and firmly into the
carousel without hesitation. DO NOT HOVER over
the carousel as it sometimes will cause the cleaning pad to be sucked up
and thrown out.
4: Place the Sander Sitter on a clean, solid
and level work surface.
Spin
Control Adjustment
Some ROS’s rotate faster than others especially
older models with worn braking mechanisms. These may appear to be unstable, or
jump out of the carousel while winding down. If this occurs, turn the Spin
Control Adjustment located in the centre of the carousel clockwise using 1/8”
allen key, until slight resistance is felt. Re adjust as necessary until the
ROS and the carousel rotate under control and stop simultaneously.
Caution
1: Do not leave a running sander unattended in
the carousel.
2: Make sure the sander is properly seated in
the carousel before releasing it
3: Do not leave the sander running in the
carousel for extended periods of time.
4: Do not apply heat to the Cleaning Pad as it
causes it to shrink.
Benefits
1: Faster working time by not having to turn
the sander off and on every time you sit it down.
2: At least 4 to 5 times longer sanding disc
life by cleaning action it provides
3: Eliminates the damage the excess paper can
cause to itself and or your work, by automatically rolling it upwards out of
the way enabling you to glide over edges and any cut out areas of your work.
4: Gives a safe resting place for your sander,
and prevents it from being damaged by falling onto the floor during “wind down”
time
Tips
1: The Crepe Rubber Cleaning Pad does not wear
thin or crumble away and will probably last forever. For maximum cleaning
action, wash crepe rubber cleaning pad regularly with cold water and soap,
rinse well and allow to air dry. DO NOT APPLY ANY FORM OF HEAT.
2: For more stability, place the Sander Sitter
on a Sanding Mat.
3: The sanders cord is the tether, so it has to
come from over the edge of the table or bench where the sander is being used. The
Sander Sitter will not work properly if the cord is hanging from above or lying
on the table from the rear or sides.
4: If the sanding disc is heavily loaded with
debris, exert slight downward pressure on the sander while it is running in the
carousel. This will add to the cleaning action for better results.
5: To mount it to a work station or a bench,
remove the cleaning pad to expose the access port to holes in the base. This
enables the Sander Sitter to be fastened down with 2 screws.
6: All ROS’s perform differently depending on
make, model and age. The Sander Sitter’s performance will vary and will enhance
itself with use depending on the individual Sander.
**Note** for “Bosch” and other palm sanders where the dust collection is
extreme. You may experience the Sander sticking to, and rotating the cleaning
pad, causing poor performance. To remedy this, cut a slit across the centre of
the Crepe Rubber Cleaning Pad (approx. 3”in length) with a knife in order to relieve
the suction caused by the Sander which prevents the carousel from spinning
freely. This will not compromise the performance or cleaning ability.
Maintenance
The Sander Sitter is relatively maintenance
free.
1: If the bearing slows down it can be cleaned
with compressed air, by blowing any excess dust out from around it.
2: Maintain Cleaning Pad by washing it with
cold water and soap, and letting it air dry.
Warranty
1 Year Manufacturer’s warranty against manufacturing
defects.
Information
Any questions or inquiries about the Sander
Sitter please contact:
Baxter Creek Tools Co. Inc.
Angus Ont. L0M 1B1
705-424-0124 or 1-866-720-0194
www.sandersitter.com
/email to inquiries@sandersitter.com