|
Sander
Sitter |
"Random
Orbital Sander
Support Station
with
Automatic Disc Cleaner" |
|
 |
|
|
| |
|
| |
|
| |
 |
From This
 To
This!
Cleans
Sanding Disc's
Automatically |
 |
Sander
Sitter 5" & 6" HD
Sander Sitter 5"
is a unique accessory that works with 5”
Random Orbital Disc Palm Sanders(ROS). The Sander Sitter allows the
operator of a ROS to safely set the Sander down in the carousel while
running to free up hands in order to maneuver work surfaces. As it is
spinning in the carousel the natural crepe rubber cleaning pad is
eliminating 70 to 80% of the debris from the sanding paper disc. It is
also utilized in the process of shutting off the Sander, by placing it
in the carousel and letting it wind down and stop safely in one place.
Sander
Sitter 6"HD is
now available. From our field tests, we have established that the
primary market will be commercial woodworking, auto-body, fiberglass,
and solid surface operations.
The Sander
Sitter 6"HD is designed to work with all 6" Random Orbital
Disc sanders, whether electric or pneumatic D/A. Included is a custom
support arm which allows the Sander Sitter 6"HD
to accommodate right angle or barrel grip sanders. D/A and D-handle
models do not require the use of the support arm.
The new Sander Sitter 6" HD
features all of the benefits of the original 5" Sander Sitter.
|
 |
Instructions :
**STEPS
1 & 2 ARE VERY IMPORTANT**
1: The first time you use a new Sander Sitter, spread some sanding dust
on the crepe rubber cleaning pad to eliminate the sticky texture of the
new cleaning pad. The sander has to slide on the pad in order to
operate smoothly.
2: Be sure the sanding disc is centered on the Sander, and the excess
overlap of the sand paper is rolled upwards. The first few times you
must do this manually, eventually the Sander Sitter will do this
automatically. This ensures enough room for movement in the carousel in
order for the ROS. to rotate and not shake.
3: Do not start the sander while it is sitting in the carousel. After
sanding, place the ROS directly and firmly into the carousel without
hesitation. DO NOT HOVER OVER THE CAROUSEL as it sometimes will cause
the cleaning pad to be sucked up and thrown out.
4: Place the Sander Sitter on a clean, solid and level work surface.
Spin Control Adjustment:
Some ROS's rotate faster than others especially older models with worn
braking mechanisms. These may appear to be unstable, or jump out of the
carousel while winding down. If this occurs, turn the Spin Control
Adjustment located in the centre of the carousel clockwise using 1/8"
allen key, until slight resistance is felt. Re adjust as necessary
until the ROS and the carousel rotate under control and stop
simultaneously.
Caution:
1: Do not leave a running sander unattended in the carousel.
2: Make sure the sander is properly seated in the carousel before
releasing it
3: Do not leave the sander running in the carousel for extended periods
of time.
4: Do not apply heat to the Cleaning Pad as it causes it to shrink.
Benefits:
1: Faster working time by not having to turn the sander off and on
every time you sit it down.
2: At least 4 to 5 times longer sanding disc life by cleaning action it
provides
3: Eliminates the damage the excess paper can cause to itself and or
your work, by automatically rolling it upwards out of the way enabling
you to glide over edges and any cut out areas of your work.
4: Gives a safe resting place for your sander, and prevents it from
being damaged by falling onto the floor during "wind down" time.
Tips:
1: The Crepe Rubber Cleaning Pad does not wear thin or crumble away and
will probably last forever. For maximum cleaning action, wash crepe
rubber cleaning pad regularly with cold water and soap, rinse well and
allow to air dry. DO NOT APPLY ANY FORM OF HEAT.
2: For more stability, place the Sander Sitter on a Sanding Mat.
3: The sanders cord is the tether, so it has to come from over the edge
of the table or bench where the sander is being used. The Sander Sitter
will not work properly if the cord is hanging from above or laying on
the table from the rear or sides.
4: If the sanding disc is heavily loaded with debris, exert slight
downward pressure on the sander while it is running in the carousel.
This will add to the cleaning action for better results.
5: To mount it to a work station or a bench, remove the cleaning pad to
expose the access port to holes in the base. This enables the Sander
Sitter to be fastened down with 2 screws.
Maintenance:
The Sander Sitter is relatively maintenance free.
1: If the bearing slows down it can be cleaned with compressed air, by
blowing any excess dust out from around it.
2: Maintain Cleaning Pad by washing it with cold water and soap, and
letting it air dry.
Warranty:
1 Year Manufacturers warranty against manufacturing defects.
Information:
Any questions or inquiries about the Sander Sitter please go to the
contact section of our
web site. |
| |
|
|
|
|
|
|
|
| |
|
|
|
